The price is guaranteed， the service is guaranteed， and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device， the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard， so as to avoid some safety hazards in use.
Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation， it should be fully considered whether the site environment meets the operating conditions of the steam crane.
SongshanThe load capacity of the goods and the tonnage of the goods transported at one time also affect the lifting speed. Reaching the excellent value of the lifting platform for transporting goods is the guarantee of speed. If the goods are too heavy， the normal delivery time will also be affected.
Correct construction elevator site inspection First of all， we need to check the foundation to see if there is any water accumulation， and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission， it can be divided into two types: open type and closed type. Of course， the lift also has a lot of safety equipment.
Port LouisIt is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy， the clothing will repeatedly slap the car paint， especially if the car blows sand on the clothes， it will draw many fine scratches on it. Because it will turn black over time. In addition， when the wind does not directly spray powder or clean the sand on the mechanism， but it should be washed with water， and the scissor-type mechanical mechanism is easy to maintain， with strong stability and high carrying capacity. The maximum lifting height is about meters， and the maximum load is about tons. .
The hydraulic lifting platform can be divided into: four-wheel mobile type， two-wheel traction type， car modified type， car type， auxiliary self-propelled type， and the lifting height ranges from a meter to s meter.
The surface of the brushes of each part should be kept clean， and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory， high quality and low price. Fire-resistant-waterproof-high temperature resistant， durable， safe and reliable.
The hydraulic lifting stage rollers， balls， turntables and other table tops can be configured arbitrarily，SongshanFixed lifting cargo elevator， which can meet the requirements of different working conditions.
As for the guide rail elevator installed outdoors， it is often exposed to rain and sunlight， hydraulic lifting platform products are divided into crank arm hydraulic lifting machines， scissor hydraulic lifting machines， mast type hydraulic lifts， and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations， docks， airports， hotels， post and telecommunications， municipal gardens， garages，SongshanFive ton cargo elevator， cleaning companies， public building facade decoration， decoration or installation and maintenance of power systems， etc. The lift has the advantages of light weight self-propelled， electric start， self-supporting legs， simple operation， large working area， especially the ability to cross obstacles for high-altitude operations and the like.
Secondly， there must be no dirt on the friction surface. If there is dirt， it needs to be washed off with gasoline or thinner; the gear box， gearbox， external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found， replace them in time. If there is any looseness， it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally， whether there is noise or failure to eliminate all faults in a timely manner; when installing， dismantling and adjusting the slewing mechanism of the equipment it is necessary to pay attention to the parallelism between the reducer and the center line of the gear， and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly， whether the wires and cables are If there is damage， whether the motor is overheated，Songshan1 ton lifting 8-meter cargo elevator， replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor， each box， distribution box and brushes must be kept clean， and the travel switch points of each safety device must be safe and reliable.
In addition， during installation， it is strictly forbidden to use hammers， etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation， clean the anti-rust oil on the motor input shaft， the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation， and to prevent unnecessary wear and tear.
The water cooling of the hydraulic station is generally tube-type water cooling， and its type selection is based on the heat load to calculate the heat exchange area， while its air-cooled elevator is carried out by using an air cooler and it is The heat transfer capacity is calculated according to the heat load， and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore， these two kinds of cooling are not the same， and there is a big difference. Long-term promotion of freight elevator factories and other， Long-term cooperation， you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently， I have seen many netizens report the problem of very loud oil cylinders. Today the editor will simply popularize the knowledge for everyone.
Installation material listFixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines， materials on and off the assembly line， parts lifting during large-scale equipment assembly， and fixed three-dimensional parking. So what is the new price of the fixed lift?
Now you understand how to use the hydraulic lift. It provides our operators with a safe working environment and improves the working efficiency and quality of the lift.
Ensure good power supply at the installation site， install a separate distribution box， and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion， the leakage switch should be adapted to the frequency converter when selecting the leakage switch .
SongshanThe common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present， this product can be said to be sold well in China， because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet， and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.
The load of this series of products is divided into . to . tons， with a load of up to tons.
Regarding the cleanliness of the hydraulic station， is there any relevant rule requirement?