Are the water cooling and air cooling of the hydraulic station the same?
The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station， so it should not be careless. Moreover from a professional point of view， there are relevant rules and requirements， and you should refer to the specification manual， so that you can have a correct understanding and know how to achieve better cleanliness.
PalermoAlways check all wires and cables for damage.
The load of this series of products is divided into . to . tons， and can also be customized according to user requirements， stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.
The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding， the short-circuit current is much larger than the normal operating current，PalermoProfessional cargo elevator， which increases the copper loss of the winding causing the winding to overheat and even burn out.
Test the freight elevator every day to see if the freight elevator can operate normally.
The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants， restaurants， restaurants， etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits， and there is no need to set up hanging points on the top， which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode， and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected， or one of the parallel branches is disconnected， the three-phase current will be unbalanced and the motor will overheat.
Precautions for daily maintenance of hydraulic lifts Check all hydraulic pipes and joints of hydraulic lifts. The pipes must not be damaged， the joints must not be loose， and all joints must be tightened.
The last thing to note is that， compared with the lifting platforms in some places， protective fences are generally added on the platforms. Since the lifting platforms are special equipment， the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled， so when the personnel ask you if you want to add a guardrail， don"t blindly refuse， and consider whether it is necessary according to the site of use. In addition， you must have the "People"s Republic of Special Equipment Manufacturing License" and the "People"s Republic of Special Equipment Installation， Transformation and Maintenance License" to produce， install，PalermoSimple lifting cargo elevator for factory building， and maintain. Therefore， you must ask whether the manufacturer has these two certificates.
howAs for the guide rail elevator installed outdoors，Palermo13 meter guide rail type cargo elevator， it is often exposed to rain and sunlight， so special attention should be paid to regular maintenance and inspection to avoid accidents.
What kind of function can be achieved by installing the elevator? Before installation， confirm whether the motor and the elevator are intact， and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor the input shaft and the groove of the elevator. Fitting tolerances.
Ensure good power supply at the installation site， install a separate distribution box， and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion， the leakage switch should be adapted to the frequency converter when selecting the leakage switch .
Many people think that the strength of the elevator itself is relatively high when using the elevator， so they did not strictly follow the installation method in the manual during the installation process， but they do not know that this will cause increased wear and tear of the parts and inflexible operation， and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation， use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore， when you install the elevator， please be sure to strictly follow the installation and use related matters below， and assemble and use it carefully.
Welcome to inquireWhether it is used outdoors or indoors， some small problems will inevitably appear after a long period of time. At this time， what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem， and I will answer it with you.
How to maintain the elevator in winter? One reason is also the primary reason. Many workers in other industries do not know that the hydraulic oil of hydraulic elevators is also used in summer and winter. freeze. After entering the low temperature in winter， which is suitable for operation at low temperature.
The hydraulic lifting platform can be divided into: four-wheel mobile type， car modified type， car type， auxiliary self-propelled type， and the lifting height ranges from a meter to s meter.
PalermoLow cost: The cost is much lower than that of the scissor-type mobile lifting platform， so when purchasing a lifting platform， you must consider the scope of use of the lifting platform， the frequency of work， the load and other factors to choose a lifting platform that suits the work requirements .
Walking: assisted self-propelled， two-wheel traction， self-driving， and car modified.
Mechanisms: Mechanisms such as tabletops track grooves， wire ropes， chains， and pulleys are made of solid materials to ensure safety.