Hydraulic pump station: special pump station for domestic lifting platform， protection device outside the pump station imported from Italy: organ m type， mesh type，Bohong tribeHydraulic lifting cargo elevator， iron plate seal type.
Check the limit switch to see if all the limit switches are loose. If so， please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts， nuts， screws， etc. are loose if any，Bohong tribeFixed guide rail lifting cargo elevator， should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)
Bohong tribeAlways check all wires and cables for damage.
Nowadays， small and medium-sized enterprises are holding products with the idea of good quality and favorable price.
BuulkubSystem: explosion-proof electronic control system， remote control system， P IC system.
What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers， different materials， different rated loads， and different brand awareness， the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons， height of meters， table size mm *mm， the price is about - yuan; the rated load is - tons， the height is meters， the table size is mm*mm， the price is about yuan. Rated load， lift height， table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)
Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.
In the construction elevator， the switch box also has leakage protection equipment. Its wires and cables are well insulated， without leakage， and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements， and there is no problem of broken strands and diameter reduction. Of course， the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.
Manual hydraulic lifting platform application manual hydraulic platform performance: manual hydraulic platform vehicle is made of high-strength steel， the design structure is reasonable and compact， stable and reliable， built-in safety valve， fully sealed oil cylinder， manual hydraulic system lifting， easy to operate. Equipped with guide wheels to save the operator"s physical strength， and can protect the load wheels and pallet load wheels. Unique hydraulic pump design， the pump is simple and designed to maintain an ideal height for assembly line loading and unloading operations; coupled with the unique design concept，Bohong tribeConstruction site lifting and cargo elevator lifting， the operator"s operation is simple and convenient.
Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line， the loading and unloading of materials， the adjustment of the working height during the assembly of the workpiece， the feeding of the installed machine at a high place， the lifting of parts during the assembly of large equipment， and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods， car lifting， fixed three-dimensional parking and other places.
how muchSystem: explosion-proof electronic control system， remote control system， P IC system.
The daily maintenance of the hydraulic lifting platform in normal use is essential， but even if there is normal maintenance on the equipment any possible problem cannot be ignored， so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today， transport flammable and explosive products and other products.
Ensure good power supply at the installation site， install a separate distribution box， and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion the leakage switch should be adapted to the frequency converter when selecting the leakage switch .
market priceIt is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.
Because the maintenance is not in place in time， and its type selection is based on the heat load to calculate the heat exchange area， while its air-cooled elevator is carried out by using an air cooler， and it is The heat transfer capacity is calculated according to the heat load， and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore， these two kinds of cooling are not the same and there is a big difference. Long-term promotion of freight elevator factories and other， Long-term cooperation， mutual benefit and win-win. If you choose the wrong supplier， you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently， I have seen many netizens report the problem of very loud oil cylinders. Today， the editor will simply popularize the knowledge for everyone.
Bohong tribeThe design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod， if there is a problem with the design size and angle， then there will definitely be problems in the later stage. Therefore， it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make， the angle of the oil cylinder is slightly deviated， it will cause the friction between the cylinder barrel and the rod， which will cause the sound; the seal quality of the hydraulic lifting platform is different， and the use of different seals will also affect the sound of the oil cylinder， and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud， and long-term wear and tear may scratch the oil cylinder and cause oil leakage， so when the hydraulic lifting platform is used， pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in， it is not ruled out that the above three situations are normal， and there will still be noises. If there is no problem after investigation， then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.
Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation， it should be fully considered whether the site environment meets the operating conditions of the steam crane.
Unscrew the screw on the dust-proof hole outside the flange of the elevator， adjust the PCS system ring to align the side hole with the dust-proof hole， and tighten the inner hexagon. After that remove the motor shaft key.