Buffer. In order to increase the energy for the car to hit the top or sink to the bottom. Remove rubber or sponge from the buffer and cabin to increase their impact energy; Rope groove slipping and other accidents caused the car to suddenly fall， resulting in a safety clamp. To prevent breakage of the lifting wire rope. A safety clamp that can simultaneously cut off the power supply and stop the car from falling should be removed from the car. A car without safety tongs is not allowed to ride or carry people. If it is a simple electric elevator， there should be a safety device (such as a safety stop pin) to prevent people from suddenly falling when loading and unloading goods in the car; Electric elevators with three or more floors (including three floors) for passengers or passengers.
It is understood that the scissor type lifting platform is a widely used specialized equipment for high-altitude operations. Its shear fork mechanical structure provides high stability for the lifting platform， wide working platform， and high load-bearing capacity， making the range of high-altitude operations larger and suitable for multiple people working simultaneously. The lifting power is divided into V， V or V power supplies， diesel engines， using Italian and domestic hydraulic pump stations， and the table top is equipped with anti slip insulation buckle plates， and safety features. Please rest assured to use.
RusendalBefore each shift of work insulation， the safety devices of the construction electric elevator should be inspected to ensure sensitivity and reliability.
When the distance between the outer edge of the construction electric elevator and the edge line of the external overhead power line cannot meet the requirements in the table above， effective protective measures should be taken.
AksuAfter the electric elevator passes the inspection，RusendalHorqin ， the user unit shall organize the leasing unit installation unit， and supervision unit to conduct acceptance. For the implementation of construction general contracting， the acceptance shall be organized by the construction general contracting unit. The acceptance form should be signed by the relevant responsible person.
Setting requirements: The layout and installation of all cables and wiring of electric elevators should be able to prevent mechanical damage.
Construction electric elevators outside the lightning protection range
The distance between the electric hoist and overhead line in Electrical safety construction shall meet the specification requirements， otherwise protective measures shall be taken.
Platform.
The net height of the landing door opening should not be less than m， and the difference between the net width and the outlet width of the cage door should not exceed mm. When the floor door is closed， except for the gap between the lower part of the door that should not exceed mm， the size of any through-hole and opening related to the distance between any door and adjacent moving parts，RusendalHongshan， as well as the gap around the door or between parts，RusendalJincheng， should comply with the provisions of Table of "Mechanical Safety - Safety Distance to Prevent Upper and Lower Limbs from Touching Dangerous Areas" GB-.
Excellent qualityHorizontal lead screw mechanical electricity
Monthly maintenance and inspection of hydraulic lifting platform rollers， intermediate shafts and bearings， oil cylinder pin shafts and bearings， boom hinge shafts and bearings for wear. Add some oil to each part to extend the service life of the lifting platform bearings. The quality and level of hydraulic oil. The lifting platform should be raised throughout the entire process， and at this position， the hydraulic ground should be - millimeters higher than the bottom of the box. If the hydraulic oil becomes dark， sticky， or has foreign objects such as gravel， it should be replaced in a timely manner ( # hydraulic oil). Annual maintenance and inspection of all hydraulic pipelines and joints of the lifting platform. The pipeline must not be damaged， and the joints must not be loose. All joints must be tightened. Remove and disassemble the lowering valve of the lifting platform， blow out the plunger with compressed air， then install it and reinstall it. Drain and discard the hydraulic oil， tighten the joint， remove the oil filter， clean it with compressed air， which should cover the opening with its full width， and should not open towards the lifting passage.
average methodIt is understood that the scissor type lifting platform is a widely used specialized equipment for high-altitude operations. Its shear fork mechanical structure provides high stability for the lifting platform， wide working platform， and high load-bearing capacity， making the range of high-altitude operations larger and suitable for multiple people working simultaneously. The lifting power is divided into V， diesel engines， using Italian and domestic hydraulic pump stations， and the table top is equipped with anti slip insulation buckle plates， which have anti slip， insulation and safety features. Please rest assured to use.
Before use， they should be replaced in a timely manner to prevent major accidents.
The bearing capacity of the building structure at the attachment point of the wall bracket should meet the requirements specified in the user manual for construction electric elevators.
RusendalA complete lifting platform accessory can be selected and customized according to different places we should observe whether there is any damage to the electric elevator. We can conduct a no-load test to raise and lower it. If there are any damaged parts， venues， and environmental usage conditions. Meet the needs of different users. So why lifting platforms can be used and installed in so many industries and places is because they can achieve multi-purpose， demonstrate multifunctional， meet various different needs， and win market demand. In modern industrial transportation processes， lifting platforms have begun to play an increasingly important role， whether in airports， docks， warehouses， floors， workshops and other places that require rapid loading and unloading of goods， they have played a very practical value， long-term operation and use of these devices inevitably lead to wear and consumption， and regular maintenance and upkeep are essential. Otherwise， both work efficiency and utilization rate will decrease， and at that time， the gains and losses will outweigh the losses.
Setting requirements: The foundation and foundation of the construction electric elevator should meet the requirements of the user manual. Before installing the construction electric elevator， the foundation should be inspected and accepted according to the requirements of the specifications. Only after passing the inspection can the installation be carried out.
Installation and dismantling personnel and drivers should hold certificates to work.