Fault phenomenon: high current or tripping during unit startup， which has excellent thermal insulation performance， storage and circulation effect and reduces operation energy consumption. Of course， more important is the choice of refrigeration system. For example， at present， the refrigeration system of fluorine refrigerant is still the mainstream， but when selecting the type and power of cooling equipment， it is necessary to calculate the data for the installation of cold storage， and then make a high-quality choice.
RoselleThe general installation of air-conditioned storage will use air coolers for refrigeration. In this case， the temperature of such a controlled atmosphere reservoir may be too low. It is suggested that the unit can adjust the scale a little larger in the process of temperature setting.
Suggestions on the quantity of polyurethane cold storage insulation materials: cold storage investment is a long-term and profitable investment. A high quantity of hair can certainly reduce the initial investment， but it is necessary to grasp a certain limit and comprehensively consider the long-term energy consumption and initial investment， because the insulation effect of polyurethane cold storage insulation materials has a parabolic linear correlation with its bulk weight; A large number of studies have shown that the foam bulk density has better thermal insulation performance at ~ kg / cubic meter. Therefore，RoselleInstallation price of fresh-keeping cold storage， it is usually recommended that the number of thermostat refrigeratory outlets should be ~ square / ton.
SialkotThe installation of top warehouse plate should be carried out alternately with the installation of wall plate， and the wall plate should leave a gap for withdrawing construction equipment; During the installation of the top warehouse plate， the end steel sheet at the overlap with the wall plate shall be disconnected for mm to prevent the cold bridge from running cold; Two layers of foaming materials shall be evenly and continuously punched on the joint surface between each top warehouse plate. Rivets shall be pulled and fixed at the internal and external lap joints of the steel plate， and the rivet spacing shall be mm; According to the design drawings，RoselleAssembly cold storage price， if there are supporting beams， columns and supporting steel frames in the warehouse， the setting out and positioning shall be carried out and accurate and clear marks shall be made according to the requirements of the design drawings; Weld or install the support beam， column， support steel frame， etc. and the welded junction shall be moisture-proof and treated according to the drawing requirements.
The water tank is designed to be separated from the machine body and is double-layer. It will not drip due to condensation caused by internal and external temperature difference. It can be interlocked with the refrigeration system， that is， it will not be humidified during refrigeration to prevent serious frosting of the fan.
The combined cold storage door starts frequently or does not start for a long time or does not stop for a long time， or stops before the storage temperature reaches.
How to maintain the refrigeration compressor in the cold storage in order to prolong its service life and reduce the occurrence of faults in the use process. The refrigeration compressor in the cold storage needs regular maintenance. Here we introduce the maintenance of the compressor in the cold storage.
Before the warehouse is fixed with angle aluminum， it shall be sealed with glass glue and fixed with angle aluminum with solid pull Mao. The distance between pull rivets is mm. The distance between the upper and lower sides of the door is mm.
There are many application scenarios of cold storage， which are different. For a long time， it provides various cold storage installation， cold storage installation， cold storage construction， fruit preservation cold storage， medical cold storage， on-site settlement， honest operation， and has offices all over the country for long-term cooperation. Different purposes， functions and designs， and the appearance quality shall meet the requirements of beauty and practicality. All buttons， electrical switches， safe， long-term cold storage installation， cold storage installation， cold storage construction， fruit preservation cold storage， medical cold storage， old brand price advantage and quality guarantee! Easy to identify and operate. The indicator light shall be simple and clear. The device and each switch shall be installed on the upper side outside the warehouse door， which is easy to operate， read data and not easy to be damaged and shall be reliably fixed. The device box is installed on the door frame plate on the door opening side. The center line of the box overlaps the center line of the door frame plate. The bottom of the box is mm above the ground and is reliably fixed. The lighting lamp and door frame wire switch in the warehouse are installed directly below the device， and the height of the bottom edge of the switch box is about mm.
The equipment is built according to the application requirements of low-temperature distribution. It is reflected in the following points: a low-temperature hall，RoselleLarge cold storage engineering installation company， a closed platform， an electric sliding refrigerated door， an anti-collision flexible seal， and a platform height conditioning equipment (lifting channel) are built to complete & ldquo; Door to door & rdquo; Type loading and unloading operation has become a symbol of modern cold storage.
Operating the unit: regularly observe the oil level and oil return of the compressor and the cleanliness of the oil. If the oil is dirty or the oil level drops it shall be solved in time to avoid adverse effects.
During the installation of cold storage board in cold storage， its installation quality will directly affect the temperature of cold storage. As an important structure used in the cold storage， the cold storage board should pay attention to the details of its installation， find out the problems that are easy to be ignored， and avoid the wrong installation， which will affect the use of the cold storage or the whole installation process， so as to waste resources and increase the cost.
Product lineThe selection of equipment for the construction of equipment cold storage is closely related to the size， does it also require refrigeration? If the controlled atmosphere storage is not used for a long time after installation， it does not need refrigeration operation as long as it does not show fluorine leakage. However， there may be fluorine leakage due to long-term non use， so refrigeration operation should be carried out at this time.
After being stored in the medical cold storage project， ventilating medical products may also emit some odors. Once these odors are stored in a certain quantity， they will also have a certain impact on other products. Therefore， we must carry out regular ventilation in the process of daily use， so as to effectively reduce the storage time of products. If the medical cold storage project uses row tube refrigeration， the image of frosting may appear after use for a period of time. If we do not defrost in time， it will also affect the effect of. Therefore， reliably and accurately. Special connectors shall be used for wiring， and power protection shall be provided for the box and each power branch.
The refrigeration of cold storage pays more and more attention to the needs of environmental protection and energy saving. Professional projects include: cold storage installation， installation of cold storage， cold storage construction， fruit fresh-keeping cold storage， medical cold storage and other related businesses. Merchants who hope to have this business please consider the wide scale of warehouse temperature control， the selection and placement of cooling equipment and the description of wind speed field， which are suitable for the cold storage needs of a variety of goods. Equipped with perfect storage temperature active detection， recording and active control equipment.
