If the motor of the hydraulic lift is overheated， stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.
Today the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.
BelskbiavaPay attention to the lift during use， and place it on a solid and flat ground to prevent it from tipping over during work. Press the "Up" or "Down" button to make the workbench go up and down. Always check and maintain the various parts of the elevator. If the workbench does not move， stop it immediately for inspection. When the working pressure of the electric lift is too high or the sound is abnormal， it should be shut down immediately to avoid serious damage to the machine; the working status of the shaft pin should be checked regularly every month. If the shaft pin and screw are found to be loose， they must be locked to prevent the shaft pin from falling off. cause an accident.
The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises， municipal construction， and decoration of hotels and hotels， with reliable quality and perfect performance.
KebillyMany people think that the strength of the elevator itself is relatively high when using the elevator， so they did not strictly follow the installation method in the manual during the installation process， but they do not know that this will cause increased wear and tear of the parts and inflexible operation， use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore when you install the elevator， please be sure to strictly follow the installation and use related matters below， and assemble and use it carefully.
Before the elevator manufacturer connects the motor to the elevator， please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force， please screw on the mounting bolts at any diagonal position first， but do not tighten them tightly， then screw on the other two mounting bolts at diagonal positions， and then tighten the four mounting bolts one by one. Finally， tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?
The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding the short-circuit current is much larger than the normal operating current， which increases the copper loss of the winding， causing the winding to overheat and even burn out.
The boxes and distribution boxes of the hydraulic lift are always kept clean，BelskbiavaHydraulic lifting cargo elevator， and the dust on the electrical equipment is cleaned in time.
Boarding bridges are divided into mobile boarding bridges andBrief introduction of application range and mobile boarding bridge: high-priced elevator factory of various specifications welcomes waste dealers， industrial companies， enterprises， and power departments to visit and negotiate with the company! It is used in places where there is no loading and unloading platform on site or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site， as a remedial measure，BelskbiavaSimple lifting cargo elevator， the mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a mobile steel-structured slope， and the forklift can also directly drive into the truck compartment for batch loading and unloading operations. . Quick loading and unloading of goods can be realized with only one person operation and no power supply required.
The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod， if there is a problem with the design size and angle， then there will definitely be problems in the later stage. Therefore， it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make， the angle of the oil cylinder is slightly deviated， it will cause the friction between the cylinder barrel and the rod， which will cause the sound; the seal quality of the hydraulic lifting platform is different， and the use of different seals will also affect the sound of the oil cylinder， and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud， so when the hydraulic lifting platform is used， pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in， it is not ruled out that the above three situations are normal， and there will still be noises. If there is no problem after investigation， then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.
OK or not?The load of this series of products is divided into . to . tons， and can also be customized according to user requirements， with a load of up to tons.
The load of this series of products is divided into . to . tons， and can also be customized according to user requirements， with a load of up to tons.
Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked， and if so， replace it immediately; secondly， check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe， and if so， tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process，BelskbiavaGuide rail chain cargo elevator lifting， which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)
What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface， and if there is dirt， it must be washed off with gasoline or thinner.
DiscountWhat is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress， and new and old customers are welcome to come to consult.
What should be paid attention to when starting a new mobile lift?
Ensure good power supply at the installation site， install a separate distribution box， the leakage switch should be adapted to the frequency converter when selecting the leakage switch .
BelskbiavaIn the construction elevator， the switch box also has leakage protection equipment. Its wires and cables are well insulated， without leakage， and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements， and there is no problem of broken strands and diameter reduction. Of course， the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.
Prepare the foundation according to the foundation plan， pay attention to the alignment， leveling， and alignment to ensure the level of the foundation and various requirements for use.
The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand， it can be realized. At the same time paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.
